ElectraGlaze:esd floor wax

	ESD floor finish = MAX ESD flooring ESD Floor finish Tames the Static Beast!
CONTACT! United via e-mail		HOME
ESD Vinyl Tiles		ESD Conductive Wax
ESD Vinyl Roll Goods		ESD Carpeting
ESD Epoxy		ESD flooring Main Menu

ElectraGlaze

ESD Floor Finish

Protect and Enhance the Performance of your Static Control and Standard Floors

See the bottom of this page for THE best pricing the web has to offer on this EXCEPTIONAL ESD floor wax.

ElectraGlaze and our refined system of static control floor care products = Ultimate Performance, Conductivity and Longevity. ElectraGlaze Shine and Scuff removal? Outstanding PERIOD. If you're like most of our clients you've grown weary of seeing your resistance values rise to the point that you're hoping for a rainy day to bring them down!

NO MORE WISHFUL THINKING OR PRAYING FOR RAIN!

Easy to keep clean thanks to ElectraGlaze!

United ESD introduces a unique, wear resistant, extremely cost effective static control wax (floor finish) for use in ESD sensitive environments. Unlike typical static control wax, our advanced formulation features a proprietary, aqueous co-polymer blend of 22 active ingredients. This exclusive blend provides dramatically superior chemical, water and slip resistance. ElectraGlaze provides outstanding protection against scuff marks and abrasion in concert with outstanding electrical properties.

Highly scuff resistant.
Long lasting, reduced maintenance cost.
High gloss, esthetically pleasing luster.
Non flaking
Low tribo-charge generation
UL listed-Slip Resistant (as applied)

Low Odor, NO VOC's and Biodegradable

Application: ESD floor finish is not applied "just like" standard floor finish, take the time to understand the difference. It will save you time in the long run. This material is for use on ESD vinyl, epoxy and standard hard surface flooring. If the floor has been previously coated with a wax or "factory applied finish" (as is the case with standard VCT, OR if floor is extremely dirty, remove contaminants with emulsifying floor stripper such as ElectraStrip Floor Stripping Liquid. Power Scrub with pad, double rinse with clean water. Allow to dry thoroughly. Using a clean Rayon finish mop or wax applicator, apply thin even coats of ElectraGlaze allowing finish to dry 2 to 4 hours between coats. Two coats are recommended for optimum performance on ESD Floors, up to 5 coats are recommended for non esd floors. Buffing is not required between coats unless high luster is desired. Note: Avoid application during high humidity conditions.

Maintenance: Dry mop floors with an untreated mop daily to remove loose dirt, sand and other abrasives. As needed: damp mop using ElectraClean ESD Floor cleaner ONLY diluted 10:1 to remove soils which can degrade the coatings conductive properties and gloss. Heavily soiled areas and scuff marks can be removed by spray buffing with ElectraShine. NOTE: Do not use plain water to damp mop your floor and do not apply diluted ElectraClean for 48 hours after initial application of ElectraGlaze. If a high shine is required high speed polish with finest pad possible using coarser pads only as needed. For best results consider the use of a propane powered high speed polishing machine.

Electrostatic Decay Time EIA 541: <0.2 sec

Product Data:

% solids: >20%, ASTM D2834-34

pH: 7.25, ASTM E70-77

Gloss: 88 min, ASTM D1455-82

Recoatability: Excellent, ASTM D3153-78

Rubber Heel Marks: 1.0, ASTM D1436-82/

Resistance: Excellent CSMA # 9-73

Powdering Resistance: Excellent, ASTM D2048-82

Freeze / Thaw Stability: Passes 3 Cycles, ASTM D3209-82

Static coefficient of friction: >0.55, ASTM D2047-82

Slip Resistance per NFSI test method 101-A: 0.7 Neolite, 0.8 rubber